how to do binding on table runner?
To bind a table runner, you will need to cut strips of binding fabric that are 2.5 inches wide and long enough to go around the entire perimeter of the runner. Sew the strips together at a 45-degree angle to create one long strip. Press the strip in half lengthwise with wrong sides together.
Next, place the binding strip along the edge of the table runner with the raw edges aligned. Start sewing the binding to the runner about 6 inches from the end of the binding strip, leaving a tail of about 3 inches. Use a ¼ inch seam allowance and sew all the way around the runner, stopping about 6 inches from where you started.
Fold the binding strip up and away from the runner, then fold it back down so that the raw edge of the binding strip is aligned with the raw edge of the runner. Pin in place and sew along the fold line, making sure to catch both the front and back of the binding strip.
Continue sewing the binding to the runner in this manner until you reach the starting point. Trim the excess binding, leaving a tail of about 3 inches. Fold the end of the binding strip under and sew it in place to finish the binding.
1、 Sewing machine binding method
How to do binding on a table runner? The sewing machine binding method is a popular and efficient way to finish off the edges of a table runner. Here are the steps to follow:
1. Cut your binding strips: You will need to cut strips of fabric that are 2.5 inches wide and long enough to go around the entire perimeter of your table runner.
2. Sew the strips together: Sew the strips together at a 45-degree angle to create one long strip. Press the seams open.
3. Fold the binding in half: Fold the binding in half lengthwise and press it with an iron.
4. Attach the binding to the table runner: Starting in the middle of one of the long sides of the table runner, pin the binding to the edge of the runner, right sides together. Leave a tail of about 6 inches at the beginning.
5. Sew the binding to the table runner: Using a ¼ inch seam allowance, sew the binding to the table runner, stopping ¼ inch from the corner.
6. Miter the corners: Fold the binding up at a 45-degree angle to create a mitered corner. Then fold it back down, aligning the raw edges with the next side of the table runner. Pin in place and continue sewing.
7. Finish the binding: When you reach the starting point, overlap the ends of the binding and trim the excess. Fold the binding over the raw edge of the table runner and sew it in place.
The sewing machine binding method is a quick and easy way to finish off the edges of a table runner. It is also a great way to add a pop of color or pattern to your table decor. With a little practice, you can master this technique and create beautiful table runners for your home or as gifts for friends and family.
2、 Hand-sewn binding method
Hand-sewn binding method is a traditional and popular way to bind a table runner. Here are the steps to do binding on a table runner using this method:
1. Cut the binding fabric into strips that are 2.5 inches wide and the length of the perimeter of the table runner plus 10 inches.
2. Fold the binding strip in half lengthwise and press it with an iron.
3. Align the raw edges of the binding strip with the raw edges of the table runner, starting at one of the short ends. Pin the binding strip in place.
4. Sew the binding strip to the table runner using a ¼ inch seam allowance. Stop sewing ¼ inch from the corner, backstitch, and remove the table runner from the sewing machine.
5. Fold the binding strip up at a 45-degree angle, then fold it back down so that the fold aligns with the top edge of the table runner. Pin the binding strip in place.
6. Continue sewing the binding strip to the table runner, repeating steps 4 and 5 at each corner.
7. When you reach the starting point, overlap the binding strip by ½ inch and sew it in place.
8. Fold the binding strip over the raw edge of the table runner and hand-sew it in place using a blind stitch.
9. Repeat on the other side of the table runner.
The hand-sewn binding method is a classic technique that adds a beautiful finishing touch to a table runner. However, some modern quilters prefer to use machine binding methods for efficiency and durability. Ultimately, the choice of binding method depends on personal preference and the desired aesthetic.
3、 Bias binding method
To do binding on a table runner using the bias binding method, follow these steps:
1. Cut your bias binding strips: Cut strips of fabric on the bias (diagonal) grain of the fabric. The width of the strips should be double the desired finished width of your binding plus 1/4 inch for seam allowance.
2. Join the strips: Join the strips together at a 45-degree angle to create one long continuous strip. Press the seams open.
3. Prepare the table runner: Trim the edges of the table runner to be even and straight. Fold the edges under 1/4 inch and press.
4. Attach the binding: Starting in the middle of one side of the table runner, pin the binding to the edge with right sides together. Leave a tail of about 4 inches at the beginning. Sew the binding to the table runner using a 1/4 inch seam allowance.
5. Miter the corners: When you reach a corner, stop sewing 1/4 inch from the edge. Fold the binding up at a 45-degree angle, then fold it back down over itself, aligning the raw edge with the next side of the table runner. Pin in place and continue sewing.
6. Finish the binding: When you reach the starting point, overlap the ends of the binding and trim the excess. Fold the binding over the edge of the table runner and hand-stitch it in place.
The bias binding method is a popular way to finish the edges of a table runner because it allows the binding to curve smoothly around corners and curves. It also adds a decorative touch to the table runner. However, some people prefer other methods such as the pillowcase method or the folded edge method, depending on their personal preference and the type of fabric they are using.
4、 Double-fold binding method
To do binding on a table runner using the double-fold binding method, follow these steps:
1. Cut your binding strips: Cut your binding strips from your chosen fabric. The strips should be 2.5 inches wide and long enough to go around the entire perimeter of your table runner.
2. Sew the strips together: Sew the strips together at a 45-degree angle to create one long strip. Press the seams open.
3. Fold the binding in half: Fold the binding in half lengthwise, wrong sides together, and press.
4. Attach the binding to the table runner: Starting in the middle of one side of the table runner, align the raw edges of the binding with the raw edge of the table runner. Leave a 6-inch tail of binding at the beginning.
5. Sew the binding to the table runner: Using a ¼ inch seam allowance, sew the binding to the table runner, stopping ¼ inch from the corner.
6. Miter the corners: Fold the binding up at a 45-degree angle to create a mitered corner. Then fold the binding back down, aligning it with the next side of the table runner. Sew the binding to the next side, stopping ¼ inch from the next corner. Repeat this process for all four corners.
7. Finish the binding: When you reach the starting point, overlap the binding by ½ inch and sew it in place. Trim the excess binding.
8. Fold the binding over: Fold the binding over the raw edge of the table runner and hand-stitch it in place on the back of the runner.
The double-fold binding method is a classic way to finish a table runner. It creates a neat and tidy edge that is durable and long-lasting. One of the latest points of view is to use contrasting binding to add a pop of color or interest to your table runner. You can also experiment with different fabrics and textures to create a unique look.