how to put binding on a table runner?
To put binding on a table runner, first measure the length and width of the runner and add 10 inches to each measurement. Cut the binding fabric into strips that are 2.5 inches wide and the length of the measurements you just took. Sew the strips together at a 45-degree angle to create one long strip.
Next, fold the binding strip in half lengthwise and press it with an iron. Pin the binding to the right side of the table runner, starting in the middle of one of the long sides. Leave a tail of about 4 inches at the beginning and start sewing with a 1/4 inch seam allowance. Stop sewing 1/4 inch from the end of the first side.
Fold the binding up at a 90-degree angle and then back down, aligning the raw edge with the next side of the table runner. Sew along the edge with a 1/4 inch seam allowance. Repeat this process for all four sides of the table runner.
When you reach the starting point, fold the end of the binding under and overlap it with the beginning tail. Sew the two ends together and trim any excess fabric. Finally, fold the binding over the raw edge of the table runner and hand stitch it in place on the back side of the runner.
1、 Measure and Cut Binding Strips
To put binding on a table runner, the first step is to measure and cut binding strips. The binding strips should be cut to a width of 2.5 inches and a length that is equal to the perimeter of the table runner plus 10 inches. This will allow for enough binding to go around the edges of the table runner and have enough excess to create the corners.
Once the binding strips are cut, they should be pressed in half lengthwise with the wrong sides together. This will create a crease down the center of the binding strip that will be used as a guide when attaching it to the table runner.
Next, the binding should be attached to the table runner. Starting in the middle of one of the sides, the binding should be pinned to the right side of the table runner with the raw edges aligned. The binding should be sewn to the table runner using a ¼ inch seam allowance, stopping ¼ inch from the end of the side.
To create the mitered corners, the binding should be folded up and away from the table runner at a 45-degree angle. Then, it should be folded back down over itself, aligning the raw edges with the next side of the table runner. The binding should be pinned in place and sewn to the table runner, stopping ¼ inch from the end of the side.
This process should be repeated for all four corners of the table runner. Once all four sides are attached, the binding should be folded over to the back of the table runner and hand-stitched in place using a blind stitch.
It is important to note that there are many different methods for attaching binding to a table runner, and each quilter may have their own preferred technique. It is always a good idea to experiment with different methods to find the one that works best for you.
2、 Join Binding Strips
How to put binding on a table runner? The answer is simple: join binding strips. Binding is a finishing technique used to cover the raw edges of a quilt or table runner. It not only adds a professional touch to your project but also helps to protect the edges from fraying. Joining binding strips is an essential step in the process of binding a table runner.
To join binding strips, start by cutting your binding fabric into strips. The width of the strips will depend on the size of your table runner and the desired width of your binding. Once you have your strips cut, sew them together at a 45-degree angle to create a continuous strip. Trim the excess fabric and press the seam open.
Next, fold the binding strip in half lengthwise and press it with an iron. Align the raw edges of the binding with the raw edges of the table runner, leaving a tail of binding at the beginning. Sew the binding to the table runner using a ¼ inch seam allowance, stopping ¼ inch from the corner. Fold the binding up and away from the table runner, creating a 45-degree angle. Fold it back down, aligning the raw edges with the next side of the table runner. Sew the binding to the next side, repeating the process at each corner.
When you reach the starting point, overlap the binding tails and sew them together. Fold the binding over the raw edge of the table runner and hand-stitch it in place on the backside of the runner.
In conclusion, joining binding strips is a crucial step in binding a table runner. It creates a continuous strip of fabric that can be used to cover the raw edges of your project. With a little practice, you can master this technique and create beautiful, finished table runners.
3、 Attach Binding to Table Runner
Binding is a great way to finish the edges of a table runner. It not only adds a decorative touch but also helps to protect the edges from fraying. Here are the steps to put binding on a table runner:
1. Cut the binding strips: Cut the binding strips from the fabric of your choice. The width of the strips should be 2.5 inches and the length should be the perimeter of the table runner plus 10 inches.
2. Join the strips: Join the strips together at a 45-degree angle to create one long strip. Press the seams open.
3. Fold the binding in half: Fold the binding in half lengthwise and press it with an iron.
4. Attach the binding to the table runner: Starting in the middle of one side of the table runner, align the raw edges of the binding with the raw edges of the table runner. Pin in place and sew with a ¼ inch seam allowance. Stop sewing ¼ inch from the corner, backstitch, and remove the table runner from the machine.
5. Miter the corners: Fold the binding up at a 45-degree angle to create a diagonal fold. Then fold it back down, aligning the fold with the top edge of the table runner. Pin in place and continue sewing.
6. Finish the binding: When you reach the starting point, overlap the binding by ½ inch and sew in place. Trim the excess binding and press it away from the table runner.
7. Hand stitch the binding: Fold the binding over the edge of the table runner and hand stitch it in place.
In conclusion, putting binding on a table runner is a simple and easy process that can be done by anyone with basic sewing skills. It adds a professional touch to your table runner and makes it look more polished and finished.
4、 Miter the Corners
To put binding on a table runner, you will need to follow a few simple steps. First, cut your binding fabric into strips that are 2.5 inches wide. Then, sew the strips together to create one long piece of binding that is long enough to go around the entire perimeter of your table runner.
Next, fold the binding in half lengthwise and press it with an iron. Then, align the raw edges of the binding with the raw edges of the table runner and pin it in place. Sew the binding to the table runner using a ¼ inch seam allowance.
When you get to the corners, stop sewing ¼ inch from the edge of the table runner. Fold the binding up and away from the table runner at a 45-degree angle, then fold it back down so that the raw edge of the binding is aligned with the next side of the table runner. Pin the binding in place and continue sewing.
To finish the binding, fold it over the raw edge of the table runner and sew it in place by hand or with a machine. This will create a neat and professional-looking finish.
Mitering the corners of the binding is an important step to ensure that the corners of your table runner look neat and tidy. By folding the binding at a 45-degree angle, you create a diagonal seam that eliminates any excess fabric and creates a clean, crisp corner. This technique is commonly used in quilting and sewing projects and is a great way to add a professional touch to your table runner.